Monza Car Wash Spot Free Water Resin Filter

Monza Price £119.00

Purchase this product now and earn 119 Points!
OR

 

Description

This Monza Car Wash Spot Free Water Resin Filter has a capacity of 5.4 litres and this amazing car wash spot free car rinse water filter works wonders on leaving your car after rinsing spot free by removing most impurities in the water that normally leave spot marks and streaks behind.

This water filter is very easy to use with no hassle, just simply clip on to your garden wall tap with the hose fittings and away you go.

The length of time the resin inside it will effective for will depend on a few factors the water hardness of your area where you live and the length of time spent rinsing your car down with it connected to the filter.

Comes with hose connectors and pre filled with 3 litres of resin.

Tank size approx 18″ high x 6″ wide

Operating Specifications

Maximum pressure: 10.5 bar (150 psi)
Maximum temperature: 49 °C (120 °F)
Minimum temperature: 1 °C (34 °F)
Maximum vacuum: 127 mm Hg (5″ Hg)

DO NOT USE WITH HOT WATER, ONLY USE COLD WATER.

ONLY USE WITH COLD WATER.

Please Note: Only fill your 5.4 litre tank up with approx 3-4 litres of resin at a time.

Features

No watermarks or streaks

No need to chamois dry car down

Comes ready for you to add standard hozelock garden type connectors to begin to use immediately

Rinse and just walk away

Touchless drying = less swirl marks on your paintwork

Spot free results after rinsing

Lots of other uses: eg: motorbikes, boats, aircraft, motorhomes, hard to reach exterior windows and glass conservatories.

The life expectancy of the DI resin is based on the TDS level of the RO water going into it. The RO will
remove 95% of the TDS from the feed water.

Example: The feed water supply from a garden hose at your job site has a TDS of 300 ppm. The RO will
remove 95%, so the water going into the DI resin cartridge will be at 15 ppm. (5% of 300 ppm)

Directions For Use

Set up instructions:

1. Try and stand the filter close to your mains water tap then connect a length of hose from the mains tap on to the filter connector marked IN on the top of the filter then connect your main long length hosepipe / reel to the fitting marked OUT on the top of the filter and away you go.

Usage instructions:

1. Wash your vehicle in the normal way using warm soapy water applied with a sponge or wash mitt. Rinse the soapy water away using normal tap water directly from your hose. Keep the rinsed areas wet while you complete the whole vehicle.

Please Note: Do not allow the vehicle to dry before you rinse a second time using treated water through the filter.

2. Rinse the whole vehicle a second time using the filtered water from the top of the car downwards.

3. Stand back and allow to air dry naturally for a spot free result.

IMPORTANT TIPS:

Do not use in conjunction with a pressure washer

Use water from the filter sparingly as this will make the resin last much longer than running it all the way through the full wash process.

Only use enough filtered water for final rinse off of all surfaces

Keep using the filter resin until you are no longer satisfied with the results, then just replace the resin inside the filter when no longer giving the desired results.

We recommend that a final rinse is performed at half mains pressure so the resin will last much longer than on full mains pressure through the filter.

Monza Car Wash Spot Free Water Resin Filter

Monza Price £119.00

Purchase this product now and earn 119 Points!
OR

 

Description

This Monza Car Wash Spot Free Water Resin Filter has a capacity of 5.4 litres and this amazing car wash spot free car rinse water filter works wonders on leaving your car after rinsing spot free by removing most impurities in the water that normally leave spot marks and streaks behind.

This water filter is very easy to use with no hassle, just simply clip on to your garden wall tap with the hose fittings and away you go.

The length of time the resin inside it will effective for will depend on a few factors the water hardness of your area where you live and the length of time spent rinsing your car down with it connected to the filter.

Comes with hose connectors and pre filled with 3 litres of resin.

Tank size approx 18″ high x 6″ wide

Operating Specifications

Maximum pressure: 10.5 bar (150 psi)
Maximum temperature: 49 °C (120 °F)
Minimum temperature: 1 °C (34 °F)
Maximum vacuum: 127 mm Hg (5″ Hg)

DO NOT USE WITH HOT WATER, ONLY USE COLD WATER.

ONLY USE WITH COLD WATER.

Please Note: Only fill your 5.4 litre tank up with approx 3-4 litres of resin at a time.

Features

No watermarks or streaks

No need to chamois dry car down

Comes ready for you to add standard hozelock garden type connectors to begin to use immediately

Rinse and just walk away

Touchless drying = less swirl marks on your paintwork

Spot free results after rinsing

Lots of other uses: eg: motorbikes, boats, aircraft, motorhomes, hard to reach exterior windows and glass conservatories.

The life expectancy of the DI resin is based on the TDS level of the RO water going into it. The RO will
remove 95% of the TDS from the feed water.

Example: The feed water supply from a garden hose at your job site has a TDS of 300 ppm. The RO will
remove 95%, so the water going into the DI resin cartridge will be at 15 ppm. (5% of 300 ppm)

Directions For Use

Set up instructions:

1. Try and stand the filter close to your mains water tap then connect a length of hose from the mains tap on to the filter connector marked IN on the top of the filter then connect your main long length hosepipe / reel to the fitting marked OUT on the top of the filter and away you go.

Usage instructions:

1. Wash your vehicle in the normal way using warm soapy water applied with a sponge or wash mitt. Rinse the soapy water away using normal tap water directly from your hose. Keep the rinsed areas wet while you complete the whole vehicle.

Please Note: Do not allow the vehicle to dry before you rinse a second time using treated water through the filter.

2. Rinse the whole vehicle a second time using the filtered water from the top of the car downwards.

3. Stand back and allow to air dry naturally for a spot free result.

IMPORTANT TIPS:

Do not use in conjunction with a pressure washer

Use water from the filter sparingly as this will make the resin last much longer than running it all the way through the full wash process.

Only use enough filtered water for final rinse off of all surfaces

Keep using the filter resin until you are no longer satisfied with the results, then just replace the resin inside the filter when no longer giving the desired results.

We recommend that a final rinse is performed at half mains pressure so the resin will last much longer than on full mains pressure through the filter.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Monza Car Wash Spot Free Water Resin Filter”

Your email address will not be published. Required fields are marked *